Supreme ONE-STOP composite waterproofing method
A composite waterproofing method using Supreme OS sheets and special coating materials provides high-performance elongation, elastic recovery, and adhesion.
This is a method of applying a soft SS (Sticky Soft) coat coating material while simultaneously constructing Supreme OS sheets.
It is a cold construction method that has the advantage of fast construction speed and ability to work even in winter, adopting the mutual advantages of asphalt sheet and coating material. It is a composite waterproofing method that compensates for shortcomings and has excellent followability to cracks and the behavior of the substrate.
ONE-STOP
Characteristics of composite
waterproofing method
01.
Emergence of the need for waterproofing methods required in the field
It is a construction method that is less affected by weather, season, and pre- and post-production processes at the construction site, allowing construction without skilled workers and facilitating quality control.
02.
Winter construction possible
Construction is possible even in the winter with simple maintenance measures (heating wire, heater)
03.
Construction is simple and the construction period is short.
Two-layer method: Polyester sheet construction and joint reinforcement work can be completed at the same time as coating material is applied.
4-layer construction method: Paint + sheet + paint + PET construction work can be completed at once.
04.
Securing behavior traceability
Using a soft asphalt-based coating material with excellent adhesion, elongation, and elastic recovery, there is no change in the physical properties of the coating film even after a certain period of time. It has excellent followability due to its elastic response to concrete cracks.
05.
Minimize defect factors through composite composition of homogeneous materials
To prevent defects caused by the use of dissimilar materials, the joint is double reinforced with a composite composition of polyester sheet and asphalt-based coating material. It is a watertight and stable method that laminates sheets and paint films.
06.
Excellent economic efficiency
Since the work process is carried out continuously, preparation for rainy weather is smooth and the construction period is shortened, making it highly economical.
ONE-STOP
Characteristics of composite waterproofing method
01.
Emergence of the need for waterproofing methods required in the field
It is a construction method that is less affected by weather, season, and pre- and post-production processes at the construction site, allowing construction without skilled workers and facilitating quality control.
02.
Winter construction possible
Construction is possible even in the winter with simple maintenance measures (heating wire, heater)
03.
04.
05.
06.
Construction is simple and the construction period is short.
Two-layer method: Polyester sheet construction and joint reinforcement work can be completed at the same time as coating material is applied.
4-layer construction method: Paint + sheet + paint + PET construction work can be completed at once.
Securing behavior traceability
Using a soft asphalt-based coating material with excellent adhesion, elongation, and elastic recovery, there is no change in the physical properties of the coating film even after a certain period of time. It has excellent followability due to its elastic response to concrete cracks.
Minimize defect factors through composite composition of homogeneous materials
To prevent defects caused by the use of dissimilar materials, the joint is double reinforced with a composite composition of polyester sheet and asphalt-based coating material. It is a watertight and stable method that laminates sheets and paint films.
Excellent economic efficiency
Since the work process is carried out continuously, preparation for rainy weather is smooth and the construction period is shortened, making it highly economical.
Materials used in Supreme ONE-STOP composite waterproofing method
It is a sheet made of SBS (Styene-Butadiene-Styene) modified rubber asphalt, and is a non-exposed waterproof sheet with a polyester non-woven fabric attached to the upper surface and an HDPE film attached to the lower surface.
Division | Product Name | Main ingredients |
| Sheet waterproofing material | Supreme OS Sheet | ㆍUpper surface: polyester non-woven fabric ㆍMiddle: Rubberized asphalt ㆍBottom: HD film |
Supreme PET Sheet (polyethylene terephthalate) | ㆍPlastic + polyester = special processing | |
| Paint waterproofing material | SS coat (for floor) | ㆍTwo-component type (high-speed dispersion of asphalt compound and urethane resin) |
| SS coat (for walls) | ㆍTwo-component type (high-speed dispersion of asphalt compound and urethane resin) | |
| Base treatment material | Supreme SM adhesive | ㆍOne-component type (product with improved penetration and adhesion) |
* Standard : 1.0mm * 1.0m * 20m
＊Specifications other than the above can be changed and produced at the request of the consumer.
Supreme ONE-STOP 2-layer composite waterproofing method
Construction sequence
Diagram
01. SM adhesive application
01. SM adhesive application
02. Applying SS coat and laying OS sheet
02. Applying SS coat and laying OS sheet
03. JOINT laying
03. JOINT laying
04. Construction completed
04. Construction completed
Supreme ONE-STOP 4-layer composite waterproofing method
Construction sequence
Diagram
01.SM adhesive application
01.SM adhesive application
02. First application of SS coat and laying of OS sheet
02. First application of SS coat and laying of OS sheet
03.Second application of SS coat and laying of PET sheet
03.Second application of SS coat and laying of PET sheet
04. Construction completed
04. Construction completed
Supreme ONE-STOP 2-layer composite waterproofing method
Construction sequence
Diagram
01. SM adhesive application
01. SM adhesive application
02. Applying SS coat and laying OS sheet
02. Applying SS coat and laying OS sheet
03. JOINT laying
03. JOINT laying
04. Construction completed
04. Construction completed
Supreme ONE-STOP 4-layer composite waterproofing method
Construction sequence
Diagram
01.SM adhesive application
01.SM adhesive application
02. First application of SS coat and laying of OS sheet
02. First application of SS coat and laying of OS sheet
03.Second application of SS coat and laying of PET sheet
03.Second application of SS coat and laying of PET sheet
04. Construction completed
04. Construction completed
SupremeENC
Leading the way with faith and technology
